Imposing accurate wall boundary conditions in corrective‐matrix‐based moving particle semi‐implicit method for free surface flow

Corrective matrix that is derived to restore consistency of discretization schemes can significantly enhance accuracy for the inside particles in the Moving Particle Semi‐implicit method. In this situation, the error due to free surface and wall boundaries becomes dominant. Based on the recent study on Neumann boundary condition (Matsunaga et al, CMAME, 2020), the corrective matrix schemes in MPS are generalized to straightforwardly and accurately impose Neumann boundary condition. However, the new schemes can still easily trigger instability at free surface because of the biased error caused by the incomplete/biased neighbor support. Therefore, the existing stable schemes based on virtual particles and conservative gradient models are applied to free surface and nearby particles to produce a stable transitional layer at free surface. The new corrective matrix schemes are only applied to the particles under the stable transitional layer for improving the wall boundary conditions. Three numerical examples of free surface flows demonstrate that the proposed method can help to reduce the pressure/velocity fluctuations and hence enhance accuracy further.     

基于摩擦磨损的KDP晶体固结磨料抛光垫优化

本文通过固结磨料球与KDP晶体对磨的单因素试验探究固结磨料球中反应物种类、磨粒浓度、反应物浓度、基体硬度对摩擦系数、磨痕截面积和磨痕处粗糙度的影响,试验结果表明:KHCO₃固结磨料球对磨后磨痕对称性好,磨痕处的粗糙度值低;磨痕截面积随磨粒和反应物浓度的增加而增大,随基体硬度的增大而降低;磨痕处粗糙度随磨粒和反应物浓度的增加先降低后上升,随基体硬度的增大先上升后降低;摩擦系数受磨粒和反应物浓度影响不明显,随基体硬度的增大而降低。选择KHCO₃作为反应物,Ⅰ基体,磨粒浓度为基体质量的100%,反应物浓度为15%制备固结磨料球与KDP晶体对磨后的磨痕轮廓对称度好且磨痕处粗糙度值低,以该组分制备固结磨料垫干式抛光KDP晶体,可实现晶体表面粗糙度Sa值为18.50 nm,材料去除率为130 nm/min的高效精密加工。     

Structural and phase characteristics of the diamond/matrix interfacial zone in high-resistant diamond composites

The structural-phase state of the contact zone and the factors that influence on the strength of diamond retention in the diamond carbide composites were determined. Composites were obtained by the new hybrid technology that eliminates the reheating of the metalized coating. The elaborated technology combines the thermal diffusion metallization of a diamond and the sintering by the scheme of self-dosed impregnation in a one-stage technological cycle. By the methods of electron microscopy, X-ray diffraction analysis, and Raman spectroscopy the structural and phase characteristics of the interphase boundary were investigated. The improvement of chemical and mechanical adhesion between the diamond and carbide matrix was obtained. It was shown that the specific productivity of the samples with a metalized diamond component is 39% higher than those without metallization.     

求解矩阵方程AXB+CXD=F参数迭代法的最优参数分析

本文针对求矩阵方程AXB+CXD=F唯一解的参数迭代法，分析当矩阵A，B，C，D均是Hermite正（负）定矩阵时，迭代矩阵的特征值表达式，给出了最优参数的确定方法，并提出了相应的加速算法.     

Ultrafast gas chromatography coupled to electronic nose to identify volatile biomarkers in exhaled breath from chronic obstructive pulmonary disease patients: A pilot study

An analytical method to identify volatile organic compounds (VOCs) in the exhaled breath from patients with a diagnosis of chronic obstructive pulmonary disease (COPD) using a ultrafast gas chromatography system equipped with an electronic nose detector (FGC eNose) has been developed. A prospective study was performed in 23 COPD patients and 33 healthy volunteers; exhalation breathing tests were performed with Tedlar bags. Each sample was analyzed by FCG eNose and the identification of VOCs was based on the Kovats index. Raw data were reduced by principal component analysis (PCA) and canonical discriminant analysis [canonical analysis of principal coordinates (CAP)]. The FCG eNose technology was able to identify 17 VOCs that distinguish COPD patients from healthy volunteers. At all stages of PCA and CAP the discrimination between groups was obvious. Chemical prints were correctly classified up to 82.2%, and were matched with 78.9% of the VOCs detected in the exhaled breath samples. Receiver operating characteristic curve analysis indicated the sensitivity and specificity to be 96% and 91%, respectively. This pilot study demonstrates that FGC eNose is a useful tool to identify VOCs as biomarkers in exhaled breath from COPD patients. Further studies should be performed to enhance the clinical relevance of this quick and ease methodology for COPD diagnosis.     

高居里温度铁电单晶PIN-PT的机电性能

弛豫铁电单晶Pb(In_1/2Nb_1/2)O₃-PbTiO₃(PIN-PT)相较于常用的Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃(PMN-PT)具有更高的居里温度,在高稳定性、高性能的传感器、换能器方面具有应用前景。本工作采用谐振法研究了[001]方向极化的0.66PIN-0.34PT铁电单晶的全矩阵机电性能参数。0.66PIN-0.34PT 单晶的三方-四方相变温度(T_RT)约为160 ℃,居里温度(T_C)约为260 ℃,室温压电系数d₃₃、d₃₁、d₁₅分别为1 340 pC/N、-780 pC/N、321 pC/N,介电常数ε^T₃₃、ε^S₃₃、ε^T₁₁、ε^S₁₁分别为2 700、905、2 210、1 927,机电耦合系数 k₃₃、k₃₁、k₁₅、k_t分别为 87%、58%、38%、61%。其纵向压电常数(d₃₃)和纵向机电耦合系数(k₃₃)小于 PMN-PT 单晶,但是横向压电性能(d₃₁)和剪切压电性能(d₁₅)都略高于PMN-PT单晶。另外,研究了机电耦合性能随温度的变化趋势,发现0.66PIN-0.34PT单晶在150 ℃以下有较好的温度稳定性。